ESD Primers
EPHB CR High-Build Primer for ESD Coatings
A high-build primer formulated specifically for applications involving static-sensitive products or equipment. EPHB CR is easily applied and penetrates deep into the concrete. The result is a primed surface that works in conjunction with Krypton Floors's ESD-control coatings.
PR 300 Vinyl Tile Epoxy Primer
PR 300 is an ideal primer for ESD applications where a static-control coating is being applied over vinyl tile. It is formulated with a special curing agent that provides extra bond strength, assuring a secure bond to the tile. PR 300 combines high strength and flexibility, enabling the primer to move with the tile's natural flexing, so the tile won't loosen.
ESD PR1 Conductive Black Primer
If a conductive floor coating is required, ESD PR1 can be applied as a base coat before using an ESD topcoat. This black, conductive, carbon-filled primer is applied at 6 mils (2.5 x 10 4 - 10 6 range). It should not be used with an ESD urethane topcoat.
ESD PR3 Static-Dissipative Black Primer
This primer was specifically formulated to be used with Krypton Floors's Chemi-LDR 610 ESD Slurry Coating when a static dissipative floor is required. ESD PR3 allows Krypton Floors to be flexible when designing a system to meet your needs. It is a 100% solids epoxy system.
Thin-Film ESD Epoxy Coatings Chemi-Cote ESD EP 1000 Epoxy Coating
High-gloss, high-solids, low-odor ESD coating. Typical installation requires one coat.
Chemi-Cote TM ESD EP 3000 Epoxy Coating
High-gloss, solvent-borne, VOC-compliant coating with a slight orange peel finish. Typical installation requires two coats.
Thick-Film ESD Epoxy Coatings
Chemi-LDR TM 610 ESD Self Leveler Epoxy
This high-gloss, low-odor, high-solids, 60-mil, ESD self-leveling coating is designed to be applied to floors that are too rough for a thin-film coating, but which have not deteriorated to the point where a heavy-duty floor resurfacer is needed to repair them. Typical installation is over a conductive or static-dissipative primer.
Chemi-Cote TM ESD EN 7000 Epoxy Novalac
This high-solids, low-odor, epoxy Novalac with an orange peel finish offers excellent chemical resistance against strong acids and caustics. Typical installation requires one coat.
Crystal-Stat ESD TM Coating
This transparent epoxy coating is designed to be used independently or in combination with decorative flake or colored quartz aggregate to manufacture a monolithic conductive or static dissipate (ESD) decorative floor system. This 100% solids, no odor conductive epoxy resin polymer can provide ESD control to any existing non-ESD surface; including concrete, tile, terrazzo and previously coated floors.
|
ESD Coatings
Because ESD coatings differ in their characteristics and benefits, several different types of ESD products may be required for one facility. For example, areas with heavy tow-motor traffic, light foot traffic, clean room assembly/manufacturing, solvent/chemical storage, and product handling might each require several different ESD products. That's why Krypton Floors offers a full line of ESD-control coatings.
Problems such as odor, moisture in new concrete, osmotic pressure, etc., also require an innovative product line. No single polymer type or ESD product will handle all of the conditions that can be experienced in the field. Krypton Floor's dedication to research and development in ESD control allows us to offer the most extensive and cost-effective ESD product line on the market today.
Krypton Floors ESD-control coatings offer the following benefits:
- Consistent resistance measurements when tested at 10-500 volts.
- Eliminates hot and cold spots.
- <15 volts BVG (when utilizing conductive footwear). (ChemiTop 850ESD and Chemi-LDR 610 ESD <50; Chemi-Cote ESD EN 7000 <20.)
- Dissipate a 5000-volt charge to zero in <0.1 seconds (72 0 F @ 12% RH).
- Maintain electrical conductivity throughout the entire thickness.
- Do not depend on relative humidity (RH) for electrical properties.
- Electrical properties guaranteed for five years.
Thin-Film Polyurethane Coatings Chemi-Cote TM ESD UR 5000 Polyurethane
This solvent-borne, VOC-compliant, UV-stable alphatic polyester polyurethane coating comes in a slight non-skid texture. Our urethanes also offer higher chemical resistance and are UV-stable. Typical installation requires one or two coats.
Chemi-Cote ESD WBUR 7000 Waterborne Urethane
This waterborne, low-odor aliphatic urethane offers easy sprayability for walls or workstations. It also features fast cure cycles, low VOC and easy repairability. Typical installation requires one or two coats.
ESD Resurfacer
Chemi-Top 950 ESD Epoxy Resurfacer
This low-odor, high-solids epoxy resurfacer has electrical properties throughout its entire thickness. Typical installation is a 3/16" topping applied by raking and then power-troweling. Used for badly damaged concrete or areas exposed to high abuse. Only available in a conductive range. |
